How to Get a Butane Light to Light Again
There was a time I would get then frustrated with my torch lighter not working properly. I would get so pissed off watching my lighter hiss and sputter or worse not even light at all. Nowadays I can troubleshoot most bug and prepare them in a couple of minutes and yous can also. All it takes is a but picayune flake of learning.
The most common reasons why torch lighters stop working are:
- Empty Fuel Tank
- Fuel Aligning Is To High Or To Low
- No Spark
- Clogged Burners
- Air Trapped In Fuel Lines
None of these common issues are difficult to fix and so if you have a torch lighter that isn't working and want to fix it quickly, proceed reading.
First off, exercise you have the instruction booklet that comes with most torch lighters? If so, check it out and see what troubleshooting steps your detail lighter has.
If you lot're maxim "of grade, I don't have that worthless teaching manual anymore!" Information technology'south all practiced. Most torch and cigar lighters are basically the same when it comes to this stuff.
Step one DOES YOUR TORCH LIGHTER HAVE FUEL?
The thing I do know when it comes to helping someone who has a lighter problem is to ask, "Is there fuel in it?" When you take a non-working lighter, this is probably the most common issue.
Ninety per centum of the fourth dimension I get a frustrated wait and a sharp "of course there is!" About 10 percent of the time I become a dislocated look and hear "um…I'thousand not sure."
Ok so…Does your torch lighter take fuel in it right now?
If you are screaming "Yes!! It'due south got fuel! But my torch lighter nonetheless isn't working." Move on to footstep 2.
If y'all don't have fuel in your lighter, purge your lighter, and then add some butane and see what happens. If you don't know how to purge and fill a lighter curlicue downwardly to the HOW TO FILL A BUTANE LIGHTER
Not sure if you have fuel in it? continue reading… We'll be getting to more than on that afterwards.
Ok, we take a fueled torch lighter, now what?
Step 2 DOES YOUR LIGHTER HISS, OR Practise Nil WHEN You lot DEPRESS THE TRIGGER
A torch lighter that is hissing when y'all depress the trigger means the fuel is going in the right direction.
If your torch hisses when you aren't depressing the trigger you probably have an internal leak or busted seal. That would be exterior my ability to help so get with the manufacturer.
Back to the hiss and wink or just hissing when you hit the trigger.
When you lot hit the trigger and get nothing but a hiss you might have the flame setting likewise high. Endeavour lowering the flame setting and encounter what happens. This is another common torch lighter not working effect.
Conversely, if you hit the trigger and either hear a depression hiss or nil at all try turning up the flame adjuster and come across what happens.
Footstep three ARE You GETTING A SPARK ON YOUR TORCH LIGHTER?
If afterwards adjusting your flame up or downwardly are you even so just getting a hiss or are you getting a flash and a hiss?
Continuing to get a hiss when yous depress the trigger might advise either you lot aren't getting a spark or you might demand to proceed working on the flame aligning.
When you don't take a spark it could exist a couple of things. Kickoff off, the worst-case scenario would exist that the ignition is dead. More usually, the igniter end might exist muddy.
I use a can of compressed air to blow over and clean the end of the igniter when I have a torch lighter not working properly.
Cheque to run into if you have a spark. If yous have a expert spark and hear a hiss or have a wink and hiss you're moving in the right direction.
Footstep 4 DOES YOU LIGHTER Flash OR QUICKLY FLAME OUT?
When you have a torch lighter not working correctly and striking the trigger, practice you get a quick flash or does it ignite only to burn out rapidly?
If yous get a quick flash and continues hissing and/or have a weak-looking flame grab a can of compressed air. Use the compressed air to clean out the burner or burners of your non-working torch lighter.
Impurities from cheap butane as well as pocket lint likewise as other things can clog up your burners causing problems for your lighter. Always use high-quality butane for your lighter. Click the post-obit link for a few butane brands we advise that are really high quality.
Step 5 IS YOUR TORCH LIGHTER PURGED?
Lastly, have you purged your lighter to get rid of all the air in the system?
If you aren't certain or didn't purge your lighter before filling it with butane tin can cause your lighter to flash and hiss. Non purging lighters is probably the second common issue that I see a torch lighter non working correctly.
Earlier purging your lighter make sure at that place is no lit flame or any kind around you. Also, extinguish anything like cigars or cigarettes because butane is incredibly flammable.
First, make sure your optics are protected. Use safe spectacles or goggles. Next, layout a rag on a desk-bound or table. Hold your lighter vertically and use a purging tool or small screwdriver to depress the fill stem at the bottom of your lighter.
Apply caution here! When you depress the make full stalk there will be a blast of propellant and butane that comes out quickly from the bottom of the lighter. You might have to do this several times until no more air, butane, or propellant comes out.
HOW TO REFILL A BUTANE LIGHTER – Torch Lighter Not Working Part 2
Before you purge or try to fill a butane lighter you need to make sure it is cooled off. You don't need to put information technology in the freezer or annihilation, but wait 5 minutes or so after using your torch.
Fuel Flow Adjustment
Before you refill your lighter, plough the flame adjustment all the way downwardly.
Most lighters have arrows pointing to + / – for flame top. If your lighter doesn't have these arrows, turn the aligning clockwise.
Purge the lighter.
Non that your flame adjuster is all the way down. Allow'due south purge all the air from the lighter.
Many people make the fault of trying to fill a butane lighter with purging. Every bit I mentioned above, purging means nothing more than getting all the air and whatsoever leftover propellant from your torch lighter.
When purging, Ever keep the fill/purge valve away from your confront!
Flip your lighter and then the fill/purge valve is facing up. Again, the valve is usually bottom.
Press the purge/fill stem with your screwdriver or lighter key. The air and propellant is going to blast out of the valve stem. Again, always keep the valve abroad from your face.
You'll know your lighter is completely empty when you lot can depress the valve without hearing any more air come out.
Fill your lighter with butane
Grab your butane and give your can a quick milk shake.
Flip your butane tin can so the stem is pointing downwards.
Brand sure your lighters fill valve is pointing upwardly.
Firmly button the butane nozzle downwardly over the fill valve of your lighter and press down for 5 to x seconds. Typically y'all'll hear some hissing coming from the can every bit information technology fills.
Before You Burn down Upwards Your Torch Lighter
Wait for 3 to v minutes before lighting up your torch afterwards you fill a butane lighter.
Yous may have to make some adjustments to the fuel flow/flame adjuster to get the flame the size you want.
The Conclusion to a Torch Lighter Not Working Correctly
After cleaning out your burners and igniter with compressed air and purging your lighter you lot should be good to go. If you lot're yet having problems with your torch lighter not working correctly, yous may need to contact the seller or manufacturer for assistance.
Every time I fill whatever of my torch lighters I make sure they are completely purged earlier filling with butane. Every bit a full general rule for maintenance, I as well used canned air to clean out burners and the igniter when I fill up lighters.
To make certain y'all avoid a torch lighter not working correctly just follow these simple maintenance steps.
Lastly, It is ever all-time to use highly refined butane for filling torch lighters. We recommend using quality brands like XIkar Purofane or Colibri Butane. We likewise put together a postal service on how to discover the best butane for torch lighters that also has our meridian five brands.
I genuinely hope this quick troubleshooting guide helps if yous take a torch lighter not working perfectly for you.
As always if you accept comments or questions click hither to utilize the contact page to get a hold of united states.
Source: https://toptorchlighters.com/torch-lighter-not-working/
Post a Comment for "How to Get a Butane Light to Light Again"